Request An Estimate

 

They are making a number of great points regarding How to Install a Bathtub overall in this post directly below.

Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately hard project. If the old tub is conveniently available, the project can move immediately; if you have to open a wall to get rid of the old bathtub as well as position the brand-new tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the brand-new one. Ensure you have qualified yourself for the job and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your restroom if you have actually already acquired a brand-new bathtub as well as do not need to transform the plan of your previous supply of water pipes.
Your devices as well as product checklist need to make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Removing Old Touches

If you need to change old taps with new ones as a part of your installment, after that the first thing you must do is separate the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted access that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washers are in place in between the tap and also the sink. Protect the tap in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet ports. The previous type ought to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Mounting the Tub

Using both wooden boards under its feet, position the bathtub in the called for position. The wooden boards are practical in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four little factors.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level as well as readjusting the feet on the tub up until the level reads level.
To set up taps, fit the bottom of the outermost adaptable tap adapter to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water system and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally check the overflow outlet and also the normal outlet for leakages.
Ultimately, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait till the bathtub has actually been used at the very least when as this will resolve it right into its final placement.

 

 

Getting ready for the Installation

To start with, the supporting structure supplied with the bath must be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last setting.

 

 

Tiling Around the Bathtub

In the location where the bath fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a rigid seal, causing the water to pass through the wall surface in between the bathroom and the tiling, bring about issues with dampness and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to enable the activity experienced when the tub is in usage. The sealant can break rather early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles using waterproof or waterproof glue and cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I stumbled upon that article on How to Install a Bathtub Yourself when looking around the web. Liked our review? Please share it. Let somebody else find it. Thanks for your time. Kindly stop by our website back soon.

Hot water issues?